For a sales quote, meeting request, evaluation unit, or other sales question, please fill in the form below:


Terms of Use | Privacy Policy
PSM10 Series
Photo of XS Series Power Supply

Photomultiplier Power Supply Modules

The Series PSM10 is a range of versatile high voltage component modules equally suited to both laboratory and development work and for specification in OEM equipment.  Powered from 24V DC, these units allow full range control and monitoring of voltage and current via 0-10V analogue signals. Positive or negative polarity models are available.

Model-Specific Downloads

PSM10 series brochure
 
Typical Applications Features
  • Photomultipliers
  • Piezo crystal devices
  • Ultrasonic transducers
  • Gamma cameras
  • Electron beam deflection
  • Electrorheological fluids
  • Image scanners
  • Spectroscopy
  • Scintillation counters
  • Microchannel plates
  • Electrostatic lenses
  • 10W output power
  • V & I control
  • V & I monitor
  • Output inhibit
  • High stability
  • Positive or negative polarity models
  • Short circuit and flashover protected
  • RoHS compliant to 2011/65/EU
  • CE Marked (LVD)
Specifications
Input  
Voltage 24 VDC
Current (mA) 1A max.
Output and Ordering Info Model No Output Voltage Output Current Output Power Current Load Regulation Ripple pk-pk Output Stored Charge

 
PSM10/102* 10V-1kV 10mA
 
10W 0.05% <20mV <45μC
  PSM10/202* 10V-2kV 5mA 10W 0.05% <20mV <35μC
  PSM10/502* 50V-5kV 2mA 10W 0.1% <500mV <20μC
  PSM10/103* 100V-10kV 1mA 10W 0.1% <1V <15μC
  PSM10/153* 150V-15kV 677uA 10W 0.1% <1V <110mJ
  *Please add either suffix P for positive polarity, or N for negative polarity, eg PSM10/202N for a negative polarity unit with 10v-2kV output voltage
Line regulation (VDC) Less than 0.005% change in output voltage over range 22V to 26V at rated output power
Voltage load regulation (VDC) Less than 0.005% change in output voltage for change in output current from zero to max output current at rated output voltage
Programming & Controls All Types
Voltage monitor 0 to 10V ±2% or ±100mV, whichever is greater, for 0 to maxiumum output voltage
Current monitor 0 to 10V ±2% or ±100mV, whichever is greater, for 0 to maximum output current
Output impedance 10KΩ ± 1%
Stability Less than 50ppm per hour at constant ambient temperature and rated output power after 1 hour warm-up
Enable/disable Disable: 0 to 0.8kV = off
Enable: 2.2V to 24V = on
Open circuit = on

Environmental
Temperature coefficient Less than 50ppm/°C at max output power
Operating temperature 0°C to 50°C at up to 90% RH non-condensing
Storage temperature -20°C to +70°C
Safety Meets the requirements of the Low Voltage Directive, 73/23/EEC, by complying with BS EN60950 when installed as a component part of compliant equipment.  Units are CE marked accordingly
RoHS The Series PM10 meets the requirements of EU Directive 2002/95/EC on the Restriction of use of certain Hazardous Substances in Electrical and Electronic Equipment
Thermal shock Mil-std 810, method 503-4, proc. II -40 to +65°C
Altitude Sea level to 2000 metres (6500 feet)
Reliability Mean Time Between Failure (MTBF) is greater than 100,000 hours
Protection The PSM10 is protected against continuous short circuit and flashover

 

Accuracy of specifications in unlocked documents cannot be guaranteed. Please contact your AE representative to confirm specifications.